1, time-saving: through the quick connector to split off and connecting passage, simple operation, saving time and manpower.
2, fuel-efficient: break the oil, the quick connector on the single valve can be closed oil, oil will not flow out to avoid oil pressure loss
3, environmental protection: quick connector break and connection, the oil will not spill, protect the environment.L-Type Single Way Valve Throttle Control Valve Pneumatic Components.
4, the equipment into a zero, easy to transport: large equipment or need to carry the hydraulic tools, the use of quick connector after the separation of transport, to reach the destination and then assembled.Â
5, the economy: the above advantages for customers to create the economic value.
Quick Coupler Features:
• Quick installation, simple and smart, space saving;
• Variety of styles to meet the needs of any pneumatic pipe;
• Even after installation, the plastic body can be turned freely;
• Release ring with elliptical design, easy to remove more convenient;
• All taper pipe thread pre-coated PTFE leakproof adhesive, good sealing performance.
Take over the note:
(1) to confirm the pipe cut surface perpendicular to the tube outside the scars and the tube is not oval.
(2) plug the tube must be inserted into the bottom of the joint, the tube is not inserted in the end may lead to leakage.
(3) after the tube is installed, to pull the tube to confirm the tube pulled out
When the wood unloading Note:
(4) Use the appropriate tool to remove the pipe fitting using the hexagonal part of the pipe fitting
(5) to remove the sealing material with the pipe joints with the opposite side of the sealing material. Otherwise the adhesive material may adhere to the surrounding components, resulting in failure
| Model | AC 2010-01 | AC 2010-02 | AC 3010-02 | AC 3010-03 | AC 4010-03 | AC 4010-04 | AC 4010-06 | AC 5010-06 | AC 5010-10 | |
| Rated Flow | 500 | 500 | 1700 | 1700 | 3000 | 3000 | 3000 | 4000 | 4500 | |
| Joint Pipe Bore | G1/8 | G1/4 | G1/4 | G3/8 | G3/8 | G1/2 | G3/4 | G3/4 | G1 | |
| Filtering Eleiment Roughness | 25 | |||||||||
| Highest Working Pressure | 1.0MPa | |||||||||
| Ensured Pressure Resistance | 1.5MPa | |||||||||
| Range of Adjustable Pressure | 0.05-0.85MPa | |||||||||
| Recommended Oil Use | ISO VG 32 | |||||||||
| Container Material | Polycarbonate | |||||||||
| Protective Cover | Not Available | Available | ||||||||
| Drain Function | Differential Drain | Differential Drain, Automatic Drain | ||||||||
| Valve Type | With Overflow | |||||||||
| Assembly | Filter | AW 2000-01 | AW 2000-02 | AW 3000-02 | AW3000-03 | AW 4000-03 | AW 4000-04 | AW4000-06 | AW 5000-06 | AW 5000-10 |
| Lubricator | AL 2000-01 |
AL 2000-02 | AL 3000-02 | AL 3000-03 | AL 4000-03 | AL 4000-04 | AL 4000-06 | AL 5000-06 | Â | |
â‘ Hardness:
Due to the scientific synthesis of high-molecular polyurethane elastomer materials using iron rubber, the higher the hardness, the higher the modulus, the smaller the elongation, and the better the wear resistance and heat resistance. Well, in the range of minus 35 degrees Celsius to 100 degrees Celsius, and at a pressure of 60 to 70 MPa, the maximum sealing performance can be guaranteed.
The use of viscoelastic seals made of nitrile rubber is the most complete protection against damage caused by back pressure. In the range of minus 55 degrees Celsius to 100 degrees Celsius, and under a pressure of 21MPa, due to the rubber The seal is often in a compressed state, so the compression performance of the rubber seal must be considered. It not only achieves enhanced anti-climbing performance and low friction resistance, but also has good performance in dealing with special low-temperature oil, and can also be used in combination with Anti-wear Ring double-purpose retaining ring BRL type.
Sealing products made of polytetrafluoroethylene and nitrile rubber/PTFErubber; or seals made of nylon resin and nitrile rubber, which can be used in a wide range of applications with large pressure changes and fast sliding speeds According to the working condition, the input hydraulic pressure cutout is designed on the end face of the polytetrafluoroethylene ring to prevent penetration leakage. The maximum working temperature environment is minus 40 degrees Celsius to 160 degrees Celsius; the maximum working pressure is 50MPa.
SPGW piston seal
Material:PTFE+rubber elastomer+reinforced modified nylon
Temperature:Nitrile rubber -40~100℃
Speed:=1.0m/s
Pressure:≤50mpa
SPGO piston seal
Material:PTFE+rubber elastomer
Temperature:Nitrile rubber -40~110℃
Speed:=1.0m/s
Pressure:≤35mpa
SRUV piston rod seal
Material:NBR+thermoplastic polyurethane
Temperature: -35`90℃
Speed:=0.5m/s
Pressure:≤40mpa
SRS piston rod seal
Material:PTFE+NBR
Temperature:-40~110℃
Speed:=1.0m/s
Pressure:≤40mpa
SRCB piston rod buffer seal
Material:Polyurethane+modified polyoxymethylene
Temperature: -35~110℃
Speed:=1.0m/s
Pressure:≤50mpa
SRU piston rod seal
Material:Polyurethane
Temperature:-35~100℃
Speed:=1.0m/s
Pressure:≤40mpa
SRD iron case dust prevention
Material:Polyurethane+metal skeleton material
Temperature:-40~110℃
Speed:=1.0m/s
SRDI soft dustproof
Material:polyurethane
Temperature:-40~110℃
Speed:=1.0m/
SDS Dumbbell Seal
Material:polyurethane
Temperature: -35~110℃
Speed:=0.5m/s
Pressure:≤50mpa
SPG piston combination seal
Temperature:
NBR+Polyurethane + Modified PolyoxymethyleneTemperature:-35`110℃
Speed:=0.3m/s
Pressure:≤70mpa
SRNL piston rod seal
Material
NBR+Polyurethane + Modified PolyoxymethyleneTemperature:-35`110℃
Speed:=0.3m/s
Pressure:≤70mpa
SRDF Piston Rod Seal
Material
Polyester rubberTemperature:-40`100℃
Speed:=1.0m/s
SDY Y-seal
Material:Polyurethane
Temperature:-35~110℃
Speed:=0.5m/s
Pressure:≤70mpa
KZT anti fouling ring
SDS Steffel
Piston main oil seal
oil seals,hydraulic oil seal,track link oil seal,TCV oil seal
Safe Seal Technology Co., Ltd. , https://www.jsspreals.com