How to maintain and maintain the trolley wire (slip line)

During the use of the safety trolley line, it is very important to strengthen maintenance. Many users of the trolley line system do not frequently maintain or properly maintain the inverter and cause frequent failures, affecting normal production. As we all know, the trolley wire produced by Wuhan Tianli Electric Co., Ltd. is a German company that introduced German technology. It is a leading company in the trolley line industry. The trolley wire produced by Wuhan Tianli has a large market share in many fields in China. Part of the proportion, in the same price, Wuhan Tianli Tactile Line is among the best in both quality and cost performance. In order to ensure the normal operation of the trolley line and extend its service life, the service center of Wuhan Tianli Electric Co., Ltd. is based on more than ten years of experience, summed up the daily maintenance and maintenance of the trolley line, and hopes to share with the users, as follows:

Collector brushes: If the brush is found to be loose or the wear is deflected, the cause should be ascertained and dealt with promptly. Wuhan Tianli Electric Co., Ltd. can design custom-made special slide wires and current collectors.

Collectors: Check at least once every quarter. Focus on checking the fasteners for looseness, displacement and wear of plastic parts and moving parts. Check the spring tension (the contact between the collector phone and the guide rails should be kept under certain pressure. If any problems are found, replace them in time.)

Connector: Check at least once every six months. Focus on checking whether the fastening bolts, welds and supports are loose, corroded, or displaced. If any problems are found, replace them in time.

Daily inspection: Check whether the straightness of the track has obvious deviation (>20mm), misalignment, whether the insulation protection is detached, broken or damaged, whether the stainless steel “V” groove is tilted, and whether there is foreign matter and conductive dust on the track. Wait. If necessary, check whether the insulation resistance meets the requirements (interphase insulation resistance should be ≥10M?).

In particular, daily inspections and maintenance must be strengthened for environments where track alignment, track distance, and inclination are large, use is frequent, workshop dust is too large, temperature is high, and water, acid, alkali, fog, and outdoor use environments are used.

Wuhan Tianli various types of collectors introduced:

Collector TLDJ-J (Light Security) 100A250A500A

Current collector TLGH-J (high temperature steel body) 600A1200A

Collector TLGJ-J (tube safety)

Collector TLWJ-J (seamless) 30A-140A

Wuhan Tianli Electric Co., Ltd. is the earliest company in China to develop and produce gliders. After more than ten years of domestic promotion, the number of applications of gliding lines throughout the country is beyond the reach of other regions and enterprises. With such a wide range of applications, it has played a decisive role in the market brand of Wuhan Tianli Tactile Line, creating the status of Wuhan Tianli Trolley Line brand in China. Its recommendations on the maintenance and maintenance of sliding wires, trolley wires, and current collectors are very specific and are worthy of attention and application.

Roof And Wall Panel Roll Forming Machine  is the special equipment for continuous rolling and cold-forming on steel sheet.

It adopts PPGI,GI,AL-ZINC as the raw material, decoiling the coil, continuous rolling and cold-forming, automatically cut to the size and output the finished panel. 

A Roof And Wall Panel Roll Forming Machine  is designed to produce roof panels, roofing step tiles and wall cladding sheets with different models, like IBR roofing sheets, corrugated roofing sheets, trapezoidal roof panels, IDT roofing sheets, Russian type 1100 metal step tiles, klip-lok 406 and klip-lok 700, KR18/KR24 standing seam roofing, BEMO roof sheets, and concealed fixing roofing sheets etc.

The equipment adopts PLC control, AC frequency and adjusting the speed technology, and it realizes the continuous automatically production, therefore, it is really a new type of energy-saving and high-effective producing equipment for steel structure. 

Advantages of Roof And Wall Panel Roll Forming Machine

1. Easy operation with HMI.
2.Save labor
3. Electric motor driven, with dynamos in every section
4. Different orders can be done.

5. Producing speed can reach to 15-20m/min

Technical parameters of Roof And Wall Panel Roll Forming Machine

· Uncoiler: Manual uncoiler

· Inner diameter: 480-520mm

· Outer diameter: 1250mm.

· Loading weight 5TONS

· Rotation: Pulled by main roll forming machine

· Expansion: Manually

· Forming speed: 0-12m/min.

· Forming stations: 14-18 stations

· Machine base: welded with 36 # H beam-

· Material of Shafts 45# high quality steel

· Diameter of Shafts 70mm

· Material of Roller high quality 45#steel coated with hard chrome 0.05mm.

· Thickness of Siding Plate: 18mm

· Transmission by Chain-brackets

· Motor Power 5.5 KW

· Hydraulic Cutter of the roofing cladding sheet roll forming machine

· Material of blade Cr12 with quenched treatment 48-50.

· Hydraulic Powe 3 KW

· Cutting Length and Quantity Clients can set the required length and quantity on the PLC touch screen

· Control System of roofing cladding sheet roll forming machine

· Panasonic PLC Control, LCD screen, touch screen, frequency converter

· Voltage 380V/50HZ/3phase

· Automatically measure the length and quantity

Roof And Wall Panel Roll Forming Machine

Roof And Wall Panel Roll Forming Machine,Corrugated Steel Sheet,Metal Roof Wall Panel,Color Steel Forming Machine

Botou Golden Integrity Roll Forming Machine Co.,Ltd , https://www.jcxsteelrollformer.com