In general, the size of the product to be cut, the size of the original product that can be purchased, or the actual size of the stock may vary. This requires the nesting software to provide an ideal cutting solution according to the actual situation. This is nesting. The most basic role of software. To make the nesting software competent for the various possibilities of actual production, it must have the following functions:
First, the number of CNC flame cutting machines to be large enough in size Although the actual production of each cycle will not have a large number, but in the case of budget procurement, there must be sufficient expansion, the greater the number, the general combination of optimization results More flexibility, the general optimization rate will be higher.
Second, the original film type is also large enough to actually produce 5 kinds or even more at the same time, nesting software should be more than adequate, whether customers use it or not, so that customers have the flexibility to complete kits. Of course, the results calculated by the pet-sized data cannot be used for a long time and can be calculated in a few minutes. Waiting too long for the actual application will not work.
Third, the customer generally provides order size, nesting software should be based on the size of the order to automatically compensate for edge grinding, so easy to check the error and logarithm, the corresponding label should also be the order size.
Fourth, in the optimization of typesetting, it is necessary to set the distance between the open lines of the product to keep large enough, especially for thick slices, otherwise it is difficult to open, resulting in dimensional deviation or edge quality is not good.
V. Program documents can be stored for a group of order data. All optional original films may be selected for production. In order to increase production efficiency, it is possible to select some of the original film types when the utilization ratio is not large. Therefore, each solution can be saved for comparison, without wasting time every time.
Sixth, there must be a corresponding material library to establish an original library in line with the actual, in the optimization program selection, according to the number of reflections, select a certain kind of original film, whether the need for outsourcing, the more types of original film, the fixed possibility Increasing the optimization rate will inevitably result in the difficulty of management and the reduction of production efficiency. When comparing the results of the plans, it is necessary to flexibly balance the contradictions between them.
7. Customers can classify orders that use the same original film in a similar production period, and can mix and typeset and cut, and then follow the customer's identity on the cut-out map, label the sub-frames, and take the next-step process flow respectively.
VIII. Contents of cutting diagrams The data size, serial number, customer name, code, iron frame number, etc. used for detailed numerical control flame cutting machines shall be displayed in the corresponding positions. At the same time, the open route and edge size should be displayed so that the workers can see at a glance.
Nine, edge material recycling Each worksheet will leave valuable material, you can automatically enter the material library, the next time you can call into the original film to participate in the optimization of use, to make the best use.
Ten, integration into the enterprise ERP can import data from the ERP to reduce the human input error, only need to set a good edging bit before optimization, you can directly optimize, and can optimize the results and residual material and other information exported to the ERP, to achieve the working data Unicom.
Eleventh, the complete special-shaped treatment has the commonly used unusual shape, also may import the unusual shape from AutoCad, the heterogeneous shape also needs the edging compensation, simultaneously joins the work sheet, participates in the optimized typesetting.
Twelve, CNC plasma cutting machine support For manufacturers without a cutting machine, the reference cutting diagram can be manually cut out the product, but also to achieve the purpose of saving materials, modern processing requires direct production of the corresponding processing machine code, direct drive Cutting the glass, the worker completes the entire cutting process by opening the main frame of the cut glass.
Chinese cutting machine trading network, allowing you to buy the rest assured! A variety of CNC cutting machine and CNC cutting equipment, a variety of cutting machine models, let the optional! Official website: /
Radiator Cooling Fan For Vw Audi Seat Skoda
Radiator Cooling Fan For Vw Audi Seat Skoda,Vw Polo Radiator Fan,Vw Radiator Fan,Car Electric Fan
ZHEJIANG DEYE AUTOMOBILE PARTS CO.,LTD , https://www.deyemotor.com