High-pressure water pump, the most widely used should be micro high-pressure water pump. Because of its high pressure, small size, easy to carry, and can be driven by car batteries and other characteristics, commonly used in cleaning, spraying, spraying, pressurization and so on.
First, the working principle of high-pressure water pump:
High-pressure water pump is divided into three-phase power and two-phase power, by the plunger in the plunger sleeve reciprocating motion to complete. When the plunger is in the lower position, the two water holes in the plunger sleeve are opened, the inner cavity of the plunger sleeve is communicated with the water channel in the pump body, and the water is rapidly filled in the water chamber. The plunger rises as the cam hits the roller of the roller body. Move upwards from the beginning of the plunger until the water hole is blocked by the upper end of the plunger. During this period of time, water is squeezed out of the water chamber and into the watercourse due to the movement of the plunger. So this lift is called pre-stroke. When the plunger block the water hole, it began to pressure process. Plunger up, the water pressure in the water room rises sharply. When the pressure exceeds the elastic force of the outlet valve and the upper water pressure, the outlet valve is opened and the water pressure is injected into the water pipe to be sent to the water sprayer.
The time when the inlet hole on the plunger sleeve is completely blocked by the upper end surface of the plunger is called the theoretical water supply starting point. When the plunger continues to move upward, the water supply continues all the time, and the pressure water process continues until the helical bevel on the plunger opens the plunger sleeve to return to the water hole. When being opened, the high-pressure water flows from the water chamber through the plunger Longitudinal groove and the return hole on the plunger sleeve flows back into the pump body waterway. At this moment, the hydraulic pressure in the plunger sleeve water chamber rapidly decreases, the action of the hydraulic pressure drops back to the valve seat, and the water jet immediately stops. At this point although the plunger is still up, but the water supply has been terminated. The backwater hole of the plunger sleeve is called the theoretical water supply end when the plunger bevel opens. In the plunger up the entire process of movement, only the middle of a stroke is pressurized water process, this stroke is called the effective stroke of the plunger.
Second, high-pressure pump requirements
1, the flow requirements (about 4 ~ 20 liters / minute), the pressure is not demanding (about 1 to 3 kg), mainly used for water recycling, water sampling, upgrading, etc., requiring less noise, long life, high self- Cheng, etc., optional BSP, CSP and other series;
2, low flow requirements (about 1 to 5 liters / minute), but the pressure is large (about 2 to 11 kg), mainly for spray, pressurization, car washing, etc. do not need long hours of work under high pressure or heavy load , You can choose ASP, HSP and other series;
3, for the tea table pumping, spraying, etc., require the volume as small as possible, small flow requirements, low noise (about 0.1 to 3 liters / minute), optional ASP and other series.
4, high temperature working medium (0-100 ℃), the need for pumping water or gas (water or gas may be mixed or idle, dry turn occasions), value the volume, noise, continuous use and other properties. Need pump long idling, dry turn. Pipe both water, there are gas, you need to choose water and gas dual-use pump WKA series. Micro pump WKA series is particularly suitable for use in water and gas occasions, it is water pumping, gas pumping. With the above application, you can choose WKA series.
5, the flow of greater demand (more than 20 liters / minute), but the medium contains a small amount of oil, solid particles, residues and so on.
Optional mini submersible pump QZ (in the flow of 35-45 liters / minute), QD (large flow 85-95 liters / minute), QC (large flow of 135-145 liters / minute) three series of submersible pumps, DC diving Pump.
We have two materials for our trailer door sealing gaskets. One is PVC material. We can have different colors, like whole gray, whole black, gray with white or black with white. Another material for our truck door seals is NBR material. Both two materials have their advantages. For the PVC door sealing strip, it has the price advantages. And also it has various sizes for customer choosing to suiting the diffferent sizes of the door thickness, from 18mm thickness too 100mm thickness. For the Nitrile Rubber Buna truck door sealing gasket, it has the higher quality and we can produce the complete set for the customer according to the door size. Thus customer only need to put the set on the door. It is very easy for assembly.
Trailer Door Seals,Trailer Door Security Seals,Trailer Container Door Seals,Trailer Door Gasket Seals
Jiaxing Ganland Auto Parts Co., Ltd. , https://www.gltruckparts.com