I. Introduction High-pressure liquid ammonia pump P101A / B is the key equipment of urea plant. It is a type of high-speed centrifugal pump HMP-5112 imported from SUNDSTRAND in the 1980s in the United States. The working condition is open and ready, the outlet design pressure is 27MPa, The high-speed shaft speed of 20445R / min; the outlet check valve is a single-valve swing-type high pressure self-sealing check valve, the structure and basic parameters shown in Table 1, the main role in the P101A / B automatically shut down when the pump, Prevent high pressure medium backflow and cause pump impeller to reverse, play the role of protecting P101 pump. After more than 10 years of operation, two valves seriously leak, and P101A pump outlet check valve leakage, the two failure if not resolved in time, will seriously affect the safety of urea plant, so its disassembly repair, Because of the pump outlet check valve both inside and outside the drain, the following on the valve as an example to introduce. Second, the maintenance of high pressure liquid ammonia pump outlet check valve problems (1) high pressure liquid ammonia pump outlet check valve due to long-term valve core is in working condition, the valve core wear shaft hole mill into an oval, causing the valve sink, Frequently open the seat below the sealing surface serious damage, resulting in serious leakage. (2) high-pressure liquid ammonia pump outlet check valve due to manufacturing defects and media corrosion and other reasons, the outer part of the valve body cracks appeared, leading to liquid ammonia leakage. Third, the maintenance program As the high-pressure liquid ammonia pump outlet check valve for the welding valve, subject to the inspection time, can not be offline repair. Decided to use on-site repair method to repair. Repair for leakage and leakage in two aspects at the same time: 1. Leakage repair program (1) with a small electric grinder manually seal the valve body seal surface cracks, while the surface coloring test until all the cracks and defects eliminated. (2) use A402 electrode (chrome 26 nickel 21 stainless steel electrode), with hot spot welding repair valve body sealing surface grinding Department. (3) Using a small electric mill manual grinding welding, so that the height of the valve body surface flush with the basic. (4) Production of inner ring grinding ring. (5) with the grinding ring made by hand to seal the surface grinding, grinding the inner diameter: 160.7mm. (6) according to the inner diameter of the mill served as a seal ring. 2. Internal leakage repair program (1) with a portable grinding machine seat sealing surface. Make sure it returns to a circle in the presence of cemented carbide. (2) Use four-card positioning on the lathe to find the center of the shaft center hole and reaming at the same time. (3) car system two rings (1Gr18Ni9Ti) set in the reaming. To ensure that the same in the center of the case, with a reasonable fit with the shaft, and spot welding fixed. (4) car through the shaft (1Gr13). (5) welded with tungsten carbide D547 molybdenum valve head, according to the valve seat after grinding repair valve head sealing surface. (6) After trial with Hongdan test to ensure its sealing. IV Conclusion In accordance with the above program on the high pressure liquid ammonia pump P101 outlet check valve for overhaul, a good solution to the valve leakage problem, after more than a year of operation, the use of good results, the maintenance of the same type of plant high pressure only Valve and other self-sealing valve has some reference.
Pre solder Brass Fittings's solder ring is as smooth as yorkshire and it is real no lead according to Rohs,pre solder brass fittings,solder ring brass fittings,pegler solder ring brass fittings,connex solder ring brass fittings,SR brass fittings,solder ring brass pipe fittings
presolder brass fittings,solder ring brass fittings,pegler solder ring brass fittings,connex solder ring brass fittings,SR brass fittings,solder ring brass pipe fittings
Taizhou Runde Company , https://www.nerausmotor.com