Bzw Flat Wire/Cable Inspecting Machine

Bzw Flat Wire/Cable Inspecting Machine


This full automatic flat cable inspecting machine was designed according to the regulation of the international non-standard automation equipment. It has an electronic control, high quality inspecting sensors and air circuit control. Its operation is more intuitive and accessible using new technology man-machine conversational mode. Its solid and practical design that makes the machine looks good, while it is also easy to operate. 

Functions: Inspecting flat cables and other wires. 

Product features
Wide applicable range: Mostly flat cables (length up to 190-735mm). It can also inspect other conductive wires. The length of the wire inspected has to be 50-500mm. 
High Quality: The machine is completely made of silicone and stainless steel to ensure avoiding damage. It can operate in a wide working temperature range: -5~40ºC. 
High Efficiency: BW-8 can automatically measure the length and conductivity of the wire and the damage on the terminal. It is programmed to eliminate the unqualified products and put them into the unqualified box, while dropping off the qualified products will into another box. The machine uses multi images forming system to inspect the appearance and conductivity of the wire with an inspecting speed up to 3-5 seconds/piece. 
General operating procedures
1. Manually put the wire into the loader which is applicable for many types of plastic terminals. Its final design is according to the customer's terminal sample to ensure no damaging the wire. 
2. Inspection of the damage and scratch on the surface of the wire. It is analyzed at the same time above and below. 
3. Inspection of the terminals, damage of the plastic parts and the total length of the wire. If the crimping image is not unified or the length exceeds in comparison with the standard set, the wire will be considered as defective product. 
4. Inspection of the conductivity of the wire and elimination of the unqualified products detected in the 3 previous inspections. The products that succeed in the inspection are placed into another transitioning structure. 
5. Inspected products will be packed in an exclusive plastic bag which is automatically sealed with rubber band and put into a carton. The packing quantity could be set by the touching screen. 

Technical parameters
 

  About Us
Jiangsu Bozhiwang Automation Equipment Co.,Ltd, located in the Yangze River Delta Economic center where is beautiful and rich ---Changzhou city, Jiangsu Province, China. Our company is one of the largest manufacturers for the wire processing equipments in China. The area of our company is about 10000m2, and the number of the employees is more than 300 that includes 200 outstanding technicians. Since the establishment, our company always persists the principle "the quality is the life" to develop and grow stronger.
Our company strictly follows the ISO 9000 quality standard to produce the product, and has superior aftersales service and precise processing equipments in first class, such as full automatic single end & double ends terminal crimping machine, all kinds of mute terminal crimping machines, computerized wire cutting & stripping machine, full automatic wire cutting and striping machine, pneumatic wire stripper, mute copper tape machine, PC end heading machine, all kinds of terminal crimping die, terminal blades, tensile tester, twister, computerized tubing cutting machine.
Our company aims to establish the long term, stable and mutual benefit cooperating relationship with customers from home and aboard to achieve the common development. For many years, our products have earned the reputations and good feedbacks from customers of domestic and foreign. Our products have been supplied to USA, Italy, Demark, Switzerland, Iran, Korea and Middle East market. At Present, the following famous enterprises are the users of our equipment: Shanghai Volkswagen, Yutong, Rui Kia, the Changchen, Foton, Chery and other vehicle plants. Delphi, Samsung, LG, Molex, Xi'an Hai Tian, Otis, Yong da, Kang li, Kone elevator factory and so on.
The fast development of our company is due to the conception of the science and technology which booms the factory by efficient and reliable investment,  and also persist in self innovation, to keep the advanced position in the fierce competing market. With our great efforts, our company has gained the honor of "Excellent private enterprise in Jiangsu Province" "Reliable enterprise in Jiangsu Province" and other honors.
To face the developing opportunity and challenge in the new century, Changzhou Bowang electronic equipment Co., Ltd will unites and leads all the employees, not only inherits and promotes the excellent traditions, but also develops and completes the quality of product and service, persists in pursuiting the excellence, in order to win more customer's approval and create a better future together.  Bzw Flat Wire/Cable Inspecting Machine


This full automatic flat cable inspecting machine was designed according to the regulation of the international non-standard automation equipment. It has an electronic control, high quality inspecting sensors and air circuit control. Its operation is more intuitive and accessible using new technology man-machine conversational mode. Its solid and practical design that makes the machine looks good, while it is also easy to operate. 

Functions: Inspecting flat cables and other wires. 

Product features
Wide applicable range: Mostly flat cables (length up to 190-735mm). It can also inspect other conductive wires. The length of the wire inspected has to be 50-500mm. 
High Quality: The machine is completely made of silicone and stainless steel to ensure avoiding damage. It can operate in a wide working temperature range: -5~40ºC. 
High Efficiency: BW-8 can automatically measure the length and conductivity of the wire and the damage on the terminal. It is programmed to eliminate the unqualified products and put them into the unqualified box, while dropping off the qualified products will into another box. The machine uses multi images forming system to inspect the appearance and conductivity of the wire with an inspecting speed up to 3-5 seconds/piece. 
General operating procedures
1. Manually put the wire into the loader which is applicable for many types of plastic terminals. Its final design is according to the customer's terminal sample to ensure no damaging the wire. 
2. Inspection of the damage and scratch on the surface of the wire. It is analyzed at the same time above and below. 
3. Inspection of the terminals, damage of the plastic parts and the total length of the wire. If the crimping image is not unified or the length exceeds in comparison with the standard set, the wire will be considered as defective product. 
4. Inspection of the conductivity of the wire and elimination of the unqualified products detected in the 3 previous inspections. The products that succeed in the inspection are placed into another transitioning structure. 
5. Inspected products will be packed in an exclusive plastic bag which is automatically sealed with rubber band and put into a carton. The packing quantity could be set by the touching screen. 

Technical parameters
 

  About Us
Jiangsu Bozhiwang Automation Equipment Co.,Ltd, located in the Yangze River Delta Economic center where is beautiful and rich ---Changzhou city, Jiangsu Province, China. Our company is one of the largest manufacturers for the wire processing equipments in China. The area of our company is about 10000m2, and the number of the employees is more than 300 that includes 200 outstanding technicians. Since the establishment, our company always persists the principle "the quality is the life" to develop and grow stronger.
Our company strictly follows the ISO 9000 quality standard to produce the product, and has superior aftersales service and precise processing equipments in first class, such as full automatic single end & double ends terminal crimping machine, all kinds of mute terminal crimping machines, computerized wire cutting & stripping machine, full automatic wire cutting and striping machine, pneumatic wire stripper, mute copper tape machine, PC end heading machine, all kinds of terminal crimping die, terminal blades, tensile tester, twister, computerized tubing cutting machine.
Our company aims to establish the long term, stable and mutual benefit cooperating relationship with customers from home and aboard to achieve the common development. For many years, our products have earned the reputations and good feedbacks from customers of domestic and foreign. Our products have been supplied to USA, Italy, Demark, Switzerland, Iran, Korea and Middle East market. At Present, the following famous enterprises are the users of our equipment: Shanghai Volkswagen, Yutong, Rui Kia, the Changchen, Foton, Chery and other vehicle plants. Delphi, Samsung, LG, Molex, Xi'an Hai Tian, Otis, Yong da, Kang li, Kone elevator factory and so on.
The fast development of our company is due to the conception of the science and technology which booms the factory by efficient and reliable investment,  and also persist in self innovation, to keep the advanced position in the fierce competing market. With our great efforts, our company has gained the honor of "Excellent private enterprise in Jiangsu Province" "Reliable enterprise in Jiangsu Province" and other honors.
To face the developing opportunity and challenge in the new century, Changzhou Bowang electronic equipment Co., Ltd will unites and leads all the employees, not only inherits and promotes the excellent traditions, but also develops and completes the quality of product and service, persists in pursuiting the excellence, in order to win more customer's approval and create a better future together. 

Lathe Machine Tool Holder

Cnc Lathe Chuck,Cnc Hydraulic Chuck,Rotating Hydraulic Cylinder,Lathe Machine Tool Holder

Ningbo junfa CNC Equipment Co. Ltd. , https://www.junfacnc.com