Since the relay relay coil KO is powered, the normally-opened contact KO is closed and the normally closed contact KOI is turned off. Because the impedance of the green signal lamp LD is much smaller than that of the anti-kick relay coil KO, Anti-trip relay contact KO: The anti-trip relay coil KO is kept in a power receiving state.
Due to the relay relay contact KO, disconnecting the closing circuit, no matter whether it is an accident or artificial opening, manual closing cannot be achieved. Similarly, when using the jump relay TWI in the comprehensive protector to replace the green signal, due to the jump position The resistance value of the relay coil of the relay relay TWI and the ZN 63 A vacuum circuit breaker in the anti-kick relay KO is unreasonable, and the electromagnetic interference is serious, so that the comprehensive protector emits continuous and different sound.
Improvement of the original design control loop According to the analysis of Figure 1, the vacuum circuit breaker wiring is unreasonable. Although the design idea is to directly monitor the state of the closing coil by the green signal lamp or the jumper relay TWI. The anti-trip relay coil KO is either held by the green signal lamp LD or the mutual electromagnetic interference of the jump relay TWI coil, so that normal loop control cannot be realized. The green signal lamp LD or jumper relay coil is separately led to a breaker normally closed auxiliary contact DL 4 in series. After the improvement, it can solve the problem and monitor the status of the breakers.
The use of a comprehensive protector integrated protector is an automatic protection component that integrates multiple functions such as protection, measurement, fault recording, and communication, and its superior performance is unmatched by conventional relay protection.
At present, it has been widely used in power supply systems and has the tendency to replace conventional relay protection. Many integrated protectors are equipped with an anti-trip relay TB J, which should make better use of the anti-trip relay TBJ on the integrated protector; at the same time, the jumper relay TWJ coil on the integrated protector does not have to bring out a circuit breaker normally closed auxiliary. Contact, can directly monitor the circuit breaker closing coil HQ, but must disconnect z N 63 A 0, improve the vacuum circuit breaker secondary circuit closing control diagram vacuum switch on the jumper circuit breaker KO coil connection.
Product Profile Large energy saving ceiling fans are green energy saving products of the 21st century. It has many advantages, such as powerful, no noise, zero pollution, low energy consumption. It is very popular for large masses of users. It is not only mainly used in steel structure plant, logistics warehouse, farm and other large enterprise buildings, but also agricultural markets, gymnasiums, waiting rooms, exhibition halls and other large public buildings. A large energy-saving ceiling fans with a speed of 50 revolutions per minute 1 to 3 meters per second to make the human body feels the best wind speed. A breeze from all directions gently caresses the body and increases the evaporation of human sweat. The cooling effect of 5 to 8 degrees is similar to the comfort presented by the natural breeze, which can not be matched by other fans. It is an ideal choice for indoor, ventilation and cooling in summer to remove humidity and heat. Only seven degrees of electricity per day, it can be cool for a whole summer. Energy saving comparation In summer, the sun shines directly and the indoor temperature is more than 40 degrees on average. Common industrial exhaust fans can only increase the indoor temperature. Industrial air conditioners consume thousands of kilowatts of energy every shift. There is no obvious unenclosed cooling in the space, which also increases the operating cost of enterprises. The emergence of a large energy saving ceiling fan brought the perfect solution. An energy saving fan with a diameter of 7.2meters can push the air to produce a large amount of winds effectively. The continuously rotating blades of circular form an airflow field with an effective area of 600 to 800 square meters. No other device has not yet been compared. The large energy-saving ceiling fan praduced by Linter technology has the characteristics of high reliability, feasibility and low power consumption. The controller unit used the stability of the energy-saving inverter system. In practice, the average power consumption is less than one killowatt per hour. It can guarantee more than 5,000 hours of uninterrupted operation. Linter7200 of a large energy-saving ceiling fan can cover the area of about 50 small fans of 0.75 megabytes worked. In a factory of 9000 square meters, if full coverage is to be achieved, it needs about 300 small fans or industrial 6 energy-saving fans. According to the use of four years, every eight months, every day for ten hours, can be run for 10,000 hours, about 90000kw power consumption, than the small wind 1080000kw, save 990000kw, save energy by 92%. When meeting the extreme high temperature climate, the large energy saving fans and air conditioners are used together, it will be coller. Using A large energy-saving ceiling fan for air supply can not only save the air conditioning tube, but also save more than 30% energy. Attentio Lectotype The building structure: H-shaped steel, I-shaped steel, Mixed steel square bar spherical column spherical structure. The total height of the building is more than 4, 0m, less than 15m. 1, 0m. The minimum distance between the fan and the roof is 1, 0m. The minimum safety distance between the fan blades and the obstacle is 0, 3 m. The distance between the fan blades and the wall on both sides is more than 1, 5 m. Effects of various environments on fan performance. Open space, promotes air circulation. Indoor airflow circulation in enclosed spaces is suitable for use with air conditioning. In a multi-fan environment, due to the low wind speed, caused by the fan, there will be no cyclones. The distance between the two fans will be separated before the wind will not cancel, and the coverage area will be increased at the same time. Company Information HongFa automatic door Technology (Shenzhen) Co., Ltd is a high-tech enterprise which engages in the development of advanced world-class automatic doors. Our main products include industrial fast rolling door, industrial PVC rolling door, industrial PVC rolling door, fast rolling door, rolling door, fast rolling door, rolling door, industrial automatic lifting door, industrial automatic lifting door, automatic vertical hinged door, automatic stainless steel door, automatic doors, automatic doors, electric folding gate, rolling door, automatic doors, automatic doors, automatic doors, automatic doors,
Industrial ceiling fan,electric fan,industrial fan
SHENZHEN HONGFA AUTOMATIC DOOR CO., LTD , https://www.hongfarrd.com