Morning hot car for too long or too short driving distance <br> <br> believe the owners have a lot of good habits morning hot cars, but blindly still waiting for the vehicle speed drops to normal or the water temperature rose to normal, it It's tantamount to making life difficult with your wallet. Experts suggest that drivers in most parts of China can park a vehicle for about half a minute when the vehicle is started, and then travel normally after a distance. For some northern cities, when the winter is too cold, it is appropriate to extend the time of the hot car. In addition, when the water temperature is too low, the computer will control the fuel injectors to inject more fuel. Therefore, if your commuting distance is very close, and the winter cold weather is not easy to rise to normal, then your car is It may become typical of high fuel consumption.
Tire pressure is not normal or exchange large-size tires <br> <br> experts said, because when under-inflated tire will affect fuel consumption, when the tire pressure is too small when the tire contact area with the ground increases travel resistance Bigger, then the vehicle is naturally more waste. For the same reasoning, the models with the same displacement, model, load, etc. assume that the A vehicle uses the original tire and the B vehicle uses the tire with the larger tire width. Therefore, because the vehicle's running resistance increases, the B vehicle will also have more cars than the A vehicle. Consume more fuel. Of course, if the owner fills the tire with too much air pressure and replaces tires that are too narrow in width, it will increase the likelihood of punctured tires, uneven wear on the tires, and reduced driving comfort.
No planned route, driving on congested roads, traffic jams are frequent lane changing <br> <br> many big cities will occur, and some experienced drivers will select one of the least crowded between the starting point and destination route. For this, it is recommended that the owner of the vehicle plan the route in advance and pay attention to local traffic information and road conditions to avoid congested roads. Because reducing the starting and stopping of vehicles and driving at an economical speed, this is tantamount to saving you fuel. Also, many car owners will often change lanes on the road. Not only do you need to accelerate, decelerate, and travel distances are shorter than straight lines, so this is one of the reasons for the increase in fuel consumption.
Did not regularly give the car "cleaning"
Conditional friends recommend that the appearance of the vehicle be cleaned regularly and that regular waxing of the vehicle is a good way to save fuel. The greatest resistance of the vehicle during driving comes from the air. If there is an accident in your vehicle, the vehicle body may have been deformed. This may affect the aerodynamics of the vehicle. Even slight bulges or depressions will affect the fuel consumption. The snowfall on the winter car body is also a burden on the vehicle.
Does not stall or frequent sparking <br> <br> experience a long wait for a long time without moving the vehicle idling time, it recommended that owners can choose to turn off the engine. We can often see taxi drivers choose to turn off the engine and go to the cart while they are lining up to pick up passengers. In fact, this is the best way to save fuel in the same situation.
When you are waiting for friends and being stuck on the road, it's better to turn off the engine. Every time the engine is started, the amount of fuel injected by the computer will be more, so frequent start of the engine over a period of time will definitely increase the fuel consumption of the vehicle. The automotive experts also said that the frequent start the engine, but also a fierce refueling "Child car" performance <br> <br> driving, frequent braking <br> <br> advise large before you start to see in the movies The way of hitting the throttle is very undesirable. After all, the stop line is not the starting line of the track. Follow the normal rhythm of starting, refueling, shifting, after a long period of time can save a lot of fuel. If it is not necessary when driving on the road, then it is best not to overtake the vehicle more frequently. Driving at a constant speed can reduce fuel consumption. In addition to grasping the distance between you and the car ahead, minimizing unnecessary braking actions can also bring you fuel-efficient pleasure.
Vehicles increase load without reason <br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br> Blindly adding large enclosures, tails, capstans, and luggage racks to the car will also increase the fuel consumption of the vehicle. The vehicle's fuel consumption will increase correspondingly with each additional weight. Therefore, it is recommended that all car owners make car decorations within a reasonable range. Friends who have entered an excessively erroneous zone will quickly reduce the car's burden.
Failing to fill oil numeral <br> <br> main oil viscosity index oil, 15W-40, for example, where "W" represents Winter (Winter), the smaller the number in front of which the more dilute the oil viscosity The better the fluidity is, the lower the available ambient temperature is, and the better the protection of the engine is during cold start. The figure behind “W†is the indicator of the high temperature resistance of the oil. The larger the value, the higher the oil's temperature is. The better the protection performance. Excessive selection of higher viscosity oils will increase the resistance of the engine components, which will both consume power and increase fuel consumption.
Low-speed or high-speed low speed gear <br> <br> This may happen more in the new driver, the vehicle speed many times already high and you did not have the upshift, then as the engine speed The higher and higher fuel consumption is naturally soaring, so you may wish to choose the right shift timing by referring to the vehicle's reasonable speed and gear. The other is that the vehicle's speed is too low, but it still stays at a high position. The most obvious feature of this situation is that the engine and the car body have started to shake and may turn off at any time. At this time, some friends will choose to increase the throttle. , And increasing the throttle means that the amount of fuel injection rises. The best solution to this situation is to reduce gear.
Summer windows open, air conditioning <br> <br> traffic jams summer open air car will naturally be much more comfortable, but with the rise in fuel consumption of the engine load increases. At this time, some car owners’ friends decided not to turn on the air conditioner and chose to open all the windows to cool down, but the increased driving resistance of the vehicle opening the window even when the vehicle is running would be greater than the power consumption of the air conditioner compressor. Therefore, the way to cool the window at low speed is Advisable, but it is more cost effective to open the air conditioner while driving at high speed. In addition, when the traffic jam increases, the fuel consumption of the vehicle increases, and if the air-conditioner is added, it is better to shut down the air conditioner if the traffic is congested and the temperature is acceptable.
Chlorinated polyethylene is a saturated polymer material with a white powder appearance. It is non-toxic and tasteless. It has excellent weather resistance, ozone resistance, chemical resistance and aging resistance. It has good oil resistance, flame retardancy and coloring properties. It is an excellent impact modifier for PVC plastics and a synthetic rubber with good comprehensive performance. It has a very wide range of applications and has been widely used in cables, wires, hoses, tapes, rubber and plastic products, sealing materials, flame retardant transport belt , Waterproof coiled material, film and various profiles and other products.
As a PVC impact modifier, CPE135A has many advantages such as low price, excellent performance, and excellent aging resistance, but it has certain disadvantages in the use of high impact and high hardness products and low temperature resistant products CPE135A. For example, in the formulation of rigid PVC, a large amount of CPE will reduce the hardness and rigidity, which reduces the physical properties of the product; in addition, when the low temperature resistance requirement of PVC products exceeds minus 30°C, CPE135A cannot meet the requirements. Under normal circumstances, modified CPE, such as ACM, RGC135A, etc., can be selected for rigidity and hardness improvement; for low-temperature resistance modification, impact-resistant ACR or other impact modifiers with lower glass transition temperature can be selected.
CPE 135A,Cpe-135a,Cpe 135a Impact Modifier,Impact Modifier
Henan Shunbang Chemical Industry CO.,Ltd , https://www.suspensionpvc.com