Pneumatic Ceramic Swing Discharge Gate Valve (GBZ644TC)

Pneumatic  Swing  Ceramic Feed Valve(GBZ643TC)

Characteristics:
This valve series can replace dome valves, turning valves, Bell Valves and double disc gate valves as feeding gates of store house pumps,  or can be used as an on-off device for pipelines containing abrasive dry ash, water (such as cinder water ) and the like in mines, paper making, chemical engineering and so on, as an on-off for pipelines with both soft grains and corrosive media. Its working nominal pressure is 1.0MPa, applicable temperature is below 200 Deg C, and air supply pressure is 0.6-0.8MPa.

After the valve closed, it's fully sealed in any direction. Its middle body adopts WCB steel casting and seamless steel pipe welding. Its sealing surface adopts a hard sealing element.

Its feed inlet is fully through without any blocks, and it has an automatic compressed air anti-blcikage blowing unit, with strong abrasion resistance, a good sealability, a small starting load and with  little ash sezure of accumulation.

It adopts a high-grade toughened structural ceramic seal, featuring high mechanical strength, strong abrasion resistance, a long service life and a compact structure, which can be installed at any angle.

Special ceramics is different from general ceramics, its hardness even more than steel,
second only to diamond, and corrosion resistant, high temperature resistant!!!!! "" metal
valve with long easy to produce the gap, ceramic valve is not. Because of wear-resisting,
anti-corrosive, sealing strong, ceramic water valve very water saving. "" our valves can be
used 500000 times, if every switch 60 times, can use 22.8 years, this is metal valve can not do it. "

Main Parts and Materials
Application Specification
1. Design and Manufacture: GB/T 12224
2. Face to Face Dimension: Manufacturer's Standard
3. Flange Dimension: JB/T 79.1, ANSI B16.5  DIN 2543, JIS B2020
4. Inspection and Test: GB/T 9092
5. Material Standard: GB/T 12229 for Carbon Steel, GB/T 12230 for Stainless Steel

Main External and connecting Dimensions 

  Pneumatic  Swing  Ceramic Feed Valve(GBZ643TC)

Characteristics:
This valve series can replace dome valves, turning valves, Bell Valves and double disc gate valves as feeding gates of store house pumps,  or can be used as an on-off device for pipelines containing abrasive dry ash, water (such as cinder water ) and the like in mines, paper making, chemical engineering and so on, as an on-off for pipelines with both soft grains and corrosive media. Its working nominal pressure is 1.0MPa, applicable temperature is below 200 Deg C, and air supply pressure is 0.6-0.8MPa.

After the valve closed, it's fully sealed in any direction. Its middle body adopts WCB steel casting and seamless steel pipe welding. Its sealing surface adopts a hard sealing element.

Its feed inlet is fully through without any blocks, and it has an automatic compressed air anti-blcikage blowing unit, with strong abrasion resistance, a good sealability, a small starting load and with  little ash sezure of accumulation.

It adopts a high-grade toughened structural ceramic seal, featuring high mechanical strength, strong abrasion resistance, a long service life and a compact structure, which can be installed at any angle.

Special ceramics is different from general ceramics, its hardness even more than steel,
second only to diamond, and corrosion resistant, high temperature resistant!!!!! "" metal
valve with long easy to produce the gap, ceramic valve is not. Because of wear-resisting,
anti-corrosive, sealing strong, ceramic water valve very water saving. "" our valves can be
used 500000 times, if every switch 60 times, can use 22.8 years, this is metal valve can not do it. "

Main Parts and Materials
Application Specification
1. Design and Manufacture: GB/T 12224
2. Face to Face Dimension: Manufacturer's Standard
3. Flange Dimension: JB/T 79.1, ANSI B16.5  DIN 2543, JIS B2020
4. Inspection and Test: GB/T 9092
5. Material Standard: GB/T 12229 for Carbon Steel, GB/T 12230 for Stainless Steel

Main External and connecting Dimensions 

 

1. Longmen structure using beam column integrated design, good rigidity

2. Equipped with disc knife library, tool change more quickly.

3.MPG-equipped with handwheel feeding and tool setting instrument, convenient operation, stable control.

4.Suitable for processing small injection mold, copper electrode, aluminum alloy, and electronic products processing.

5.Suitable for the medical device industry.

 

CNC Jade Engraving Machine

Stability CNC Jade Engraving Machine,Full Cover CNC Jade Engraver Machine,High Speed CNC Jade Device Machine For Engraving

Jiangsu Changzhou Jinghua Numerical Control Equipment Co.,Ltd. , http://www.jkengraving.com