Motorcycle headlight focus and distance adjustment method

Motorcycle headlights are very important for the driver to drive at night. If there is no headlight, it is equal to a scorpion walking. It is very dangerous. The motorcycle light is not as bright as possible, so it is not safe for driving at night, although you are clear. The road surface, but for the opposite driver may cause temporary blindness, which is an accident, so we must adjust the headlights of the motorcycle, which is very important for night driving safety.

How to adjust the focus and distance of the motorcycle headlights?

Here, the headlights of motorcycles (spans) are generally slightly off-right, and the left and right are generally not adjustable. Generally, they can only be adjusted in height, and of course they are adjustable. Originally this was not a circuit problem with headlights, but people who have changed bulbs will encounter such problems.

By the way: the changed bulb focus is not allowed because the position of the filament is deviated. You can compare the old bulb with the new bulb to see how much the filament position of the new bulb deviates.

If the position of the new bulb filament is low, the position of the headlight focus will be very close. To change the height of the bulb positioning ring, if the position of the new bulb filament is too high, the position of the headlight focus will be scattered. Add a homemade ring wire iron ring pad on the front of the positioning ring to lower the relative height position of the filament. After the focus is adjusted, the distance of the headlight illumination distance is well adjusted on the riding car.

Slightly loosen the screws on both sides of the fixed headlights, ride the car on the ground, turn on the headlights in the neutral position, and swing the headlights up and down slightly, and focus the headlights on the ground 20--30m away from the front of the car. Then tighten the screws that fix the headlights. If the headlights are more troublesome, please check the faucet first, then turn the bracket to adjust the lights. When the brackets are deformed, the simple point is: One side of the front headlight bracket is mounted with a hole that grows round, and when it is tightened with a screw, there is room for moving left and right.

Motorcycle headlight height adjustment:

I believe that most of the headlights of this model will be adjusted. Because this design is relatively intuitive, just use a knife or a sleeve to loosen the bolts of the two fixed headlights. You can adjust the height by moving. (In fact, this type of shape can also be appropriate to adjust the left and right illumination range of the light. The two bolt racks are slightly horizontally oriented backwards, that is, the direction of the fuel tank, and then properly adjusted).

(Do not have to adjust much, because the things above this machine, as long as the distance of 1mm will also change a lot)

Compared with the method described above, the following is actually better than the first one, but many people can't find a place. Most cars can be adjusted with only one cross-cutting knife. First find the adjustment bolt, as shown in the picture, this is my new 150, in the front of the fuel tank to pick up the lampshade to go in, look at the picture you should be able to see, that is, the white screw that the left front turn signal came back.

Here is a whole picture: you should be able to see the place more clearly, find it, then use the cross to change the knife to turn the bolt. If the headlights are too high, it will shine in the sky, then change the knife to clockwise. When the direction is rotated, you can clearly see that the light from the headlights is falling downward. If the illumination is too low and the distance is not too long, you need to use a knife to turn counterclockwise. At this time, you can clearly see the car light line up. run.

Precautions:

(1) The direction of the left and right illumination of the lamp is generally fixed, and it is generally impossible to adjust, and most of them are to the right. There is also a left-sided one.

(2) Adjusting the lights It is recommended to find a flat road with a straight line distance of about 150m+ at night.

(3) Of course, the adjustment of the lamp light does not have an absolute value, and the distance that the driver himself is more comfortable is better.

Sintered Metal Fiber Felt

Sintered Metal Fiber Felt,Sintered Felt,Metal Fiber Felt,Sintered Fiber Felt

ANPING HANKE FILTER TECHNOLOGY CO , https://www.metfilters.com